Vivotek SD8364E/ -M Manual de usuario

IP SurveillanceInstallation Guide VIVOTEK SD83XXE Speed DomeMounting AccessoriesAM-116/117 Pendant PipeAM-118 Pendant HeadAM-221 GooseneckAM-231 Parap

103. Route power lines and other wires through the pendant head. You may apply a 1 inch conduit. 4. Secure the pendant head to ceiling by driving sc

11English5. Secure the camera's top section to the pendant head by fastening 3 M5x8 screws. When done, secure the connection using an includ

12IV-1-2. Pendant Mount with Pendant Pipe: AM-116/AM-117 & AM-118 Below are the sample procedures using a pendant head and pendant pipe: 1. Determ

13English3. Route power lines and other wires through the pendant head. You may apply a 1 inch conduit. 4. Secure the pendant head to ceiling by driv

145. Secure the camera's top section to the pendant head by fastening 3 M5x8 screws. 6. Install the camera to the top section. See your Quic

15EnglishIV-2. Gooseneck Mounting: AM-221Below is a sample procedure using a gooseneck bracket: 1. Determine a hard surface wall location. Use the ali

166. Rotate the camera clockwise until its alignment mark is aligned with the "C" mark.7. Use the included T25 stardriver to tighten the 3 a

17EnglishIV-3. Parapet Mounting: AM-231The screws included in the parapet set are: Sleeve anchors 5/16" x3" 6Hex bolts M8x25 6Hex bolts M8x7

18Below is a sample procedure using the parapet mount bracket: 1. Determine a hard surface location. Use the alignment sticker to mark the positions w

19EnglishIf you install the corner parapet bracket, use the included alignment sticker, and mark the drill holes through the mounting slots on the bra

2Compatible VIVOTEK CamerasISpeed Dome SD8364E, SD8363E, SD8333E, SD83x4E, SD83x6E, SD8362EAM-118 Pendant HeadRevison History: Rev. 1.0: Initial rele

204. Use a crescent wrench to secure the outer brackets to the brackets on the wall using the M8x25 hex bolts and washers. Do not completely tighten t

21English7. Install the top section of the camera to the pipe arm by driving 3 M5 x8 screws. 8. Insert the pipe arm into the round openings on the br

229. Install the camera to the top section. For installation details, refer to the Quick Installation Guide or page 15 in this document. 10. Swivel th

23EnglishA corner parapet installation should look like this when its installation is completed.

24This page is intentionally left blank.

3EnglishAM-116 20cm Pendant Pipen 50.8172281 1/2" PS11AM-117 40cm Pendant Pipen 50.817400354281 1/2" PS111 1/2" PS1137,550,84660,317 85

4AM-221 Gooseneck405.8262.19140350 107.8165.5200278AM-231 Parapet Mount11931077.95997463228.15

5EnglishAM-231 Parapet Corner Mount11931077.95997202.95463

6AM-231 Parapet Mount - Alignment Sticker178.15100180180n 10228.15495parapet topAM-231 Corner Mount - Alignment Sticker100180180143.5287n 10495Fold Li

7EnglishPreparation before InstallationIII12Connect Ethernet cable and IO wires (this may include the AC24V wires) to the interface section of the cam

8Mounting & CablingIV446.2 mm AM-118 AM-117 AM-519 321.4 mm 204.8 mm Shown below are the dimensions of a pendant mount conguration using

9EnglishAM-519IV-1-1. Pendant Mount without Pendant Pipe: AM-118 Below are the sample procedures using a pendant head and pendant pipe: 1. Determine a